View more Product Features:Please turn the button at the bottom for to kickstand or nappingBat-at toys musical elephant sensesDeep cradle with calming vibrations soothes babiesToy easily removes for older babies sit & Jungle FunAn inclined sleeper and playtime one-now with calming The inclined baby long.Ī gentle from sleeper and Additional light-weight design for portability and storage, three-point and linkable teether. Also Fisher-Price Infant-to-Toddler Rocker, Jungle Fun is one of the top 10 sellers in Fisher-Price, Fisher-price Bouncer, Fisher-price Jumper and F in 2022. Other top elements are dos, Vibration and Removable, machine washable pad. Infant To Toddler Rocker Bouncer Seat Baby Chairġ marketplaces are selling it on Ebay with promotions. Children should not be left unattended in the Fisher Price Rainforest Jumperoo.Easily Removes For Older Babies To Sit & Play The Jumperoo can hold children who weigh less than 11.3 Kilogram and are less than 32 inches tall. The Fisher Price Rainforest Jumperoo should only be used by children who are able to hold their heads up on their own. Make sure you complete the battery installation before adding the toys to the Jumperoo base because the electronic toy will go on top of the battery compartment. It will continue to play, even if the baby stops moving, unless turned off manually by an adult. When the double music note mode is on, the music and sounds will play repeatedly for five minutes once the baby begins bouncing. The single music note mode will play music and sounds whenever the baby jumps. Pick the mode you would like to use and slide the mode switch to the correct position. Place your baby back in the Jumperoo and slide the power/volume switch to "On." You can choose one of two volume levels for the music or rainforest sounds. Snap the fasten strap bar around the strap once you have it in the correct position. You will need to pull each strap to the desired height by either raising or lowering the strap to one of the three positions. Turn the Jumperoo over and locate the height strap found under each frame tube on the actual seat assembly piece. Remove your baby from the seat to adjust the height. If this is not the case, you will need to adjust the height. Your baby's toes should just graze the floor while standing, not bouncing, and the entire foot should not touch the floor. Place your baby in the Fisher Price Rainforest Jumperoo once it is completely assembled. Slide the leaf toys into the two slots on the front two seat tubes. A clicking noise will let you know it is secure. The spots are marked and you will push each toy into place. Attach the remaining toys to the tray area, with the lizard and dragonfly going on one side and the electronic toy going on the other. Snap the rainbow toy into the peek-a-boo tiger base and place the base in the front of the Jumperoo's tray area. Place the three AA batteries into the compartment following the markings for the positive and negative sides. Insert the batteries into the base of the seat by opening the marked battery compartment with a Phillips head screwdriver. Insert the seat piece and pad into the seat ring area. Slide one of the frame tubes into a base tube, stopping when you hear a click. Hold the frame piece above the base, placing each of the three frame tubes over one of the three base tubes. Fit the six slots on the fabric cover to the corresponding pegs on the seat and attach by looping the fabric ties around the pegs. Pull the pad through the seat and wrap the edges of the fabric around the edges of the plastic seat. Line the plastic seat piece so the inside is up and the star markings are facing you. Pick up the plastic seat piece and the fabric cover. Place the large base piece onto the latch that is on the small base and push down until you hear a click. Lift the large tube base piece and place it on top of the small tube base piece. Repeat the process with the large base tube and the other hinged base assembly tube piece. Continue to push the small base tube until you hear a click. Slide the open side of the small base tube onto one of the hinged base assembly tube pieces. The two hinged base assembly pieces should now be attached. Grasp the tapered edge of the base tube on one of the hinged bases and insert it into the regular tube on the other hinged base piece.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |